We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Anti Fog Swim Goggles: 6 Steps for Clear Pool Views

Learn how to anti fog swim goggles in six simple steps, from cleaning the lenses to applying a coating, so your pool and open-water views stay clear.

Updated November 2026

To anti fog swim goggles, you need to remove the thin oily film left by manufacturing and skin, then apply a surfactant or anti-fog layer that keeps water from beading into fog. Done correctly, this takes about five minutes and can keep your lenses clear for a full training session. The steps below cover cleaning, coating, and rinsing, along with a few mistakes that undo the job.

Why Goggles Fog in the First Place

Fog forms when warm, humid air inside the goggle cup condenses on a cold lens surface. In the water, the same thing happens as tiny droplets scatter light. Most new goggles also carry a slick film from the factory and from sunscreen or skin oils, which makes water bead up instead of sheeting off. Anti-fog treatments work by changing how water spreads across the lens, so it forms a thin, invisible layer rather than droplets.

Shopping for one? See our guide: 6 Best Swim Goggles Anti Fogs for Clear Pool Views (2026).

Prepare the Lenses Before Coating

A coating only bonds well to a clean surface, so start by stripping away anything that might sit between the lens and the treatment.

  1. Rinse the goggles in warm tap water to remove chlorine residue and loose debris.
  2. Scrub each lens gently with a drop of mild dish soap or baby shampoo and your fingertip. Avoid paper towels, which can scratch the coating.
  3. Rinse thoroughly, then let the lenses air dry for about two minutes. Do not wipe them dry with a towel.

Apply the Anti-Fog Treatment

Once the lenses are clean and only slightly damp, apply the treatment. Most products follow the same general method, though manufacturers specify exact amounts and dwell times, so check the label first.

  1. Put one or two small drops of anti-fog solution on the inside of each lens, or spray lightly if your product comes in a spray form.
  2. Spread the liquid with a clean fingertip in small circles until the whole inner surface is covered.
  3. Let it sit for the time listed on the label, usually a minute or so.
  4. Rinse briefly with water or wipe gently with a clean cloth to leave a thin film behind. Avoid rubbing hard.

Owners often report that a light, even coat works better than a heavy one. Excess product can smear and leave streaks that catch light and blur vision.

Keep the Coating Working Between Sessions

The treatment wears off with every swim, so reapplying it before each session is the simplest habit. Store goggles with the lenses facing outward and away from one another to reduce contact between the inner surfaces. Rinsing with fresh water after each swim also helps remove the chlorine and salt that break the film down over time.

Choosing a Product Type

Liquid drops, sprays, and gel-style treatments all work on the same principle, so choose based on how you like to apply them. Drops give you the most control over coverage. Sprays are quicker but can drift onto the goggle strap. Make sure whichever product you choose is labeled for swim goggles rather than general-purpose glass cleaner.

Checklist for Each Session

  • Clean lenses with mild soap and water
  • Air dry without towel contact
  • Apply a thin, even layer of anti-fog treatment
  • Let it sit for the label time, then rinse or wipe lightly
  • Store goggles lens-side out to protect the coating

Common Mistakes

  • Skipping the cleaning step, which leaves oils that block the coating from bonding.
  • Applying too much product, which causes streaks and smearing.
  • Rubbing the lenses hard, which can wear away the treatment.
  • Using household glass cleaners that contain ammonia or harsh solvents that can damage goggle lenses.
  • Putting goggles on while the coating is still wet, which can leave spots.

A dedicated anti-fog product designed for swim goggles is the most direct option. Look for one labeled specifically for swim use so you know the formula suits pool or open-water conditions. View on Amazon

A soft microfiber cloth helps you rinse and wipe without scratching the lenses. Keep one dedicated to goggle care so it does not pick up grit from other gear. View on Amazon

A small goggle storage case protects the lenses between sessions and keeps the coating from rubbing against other surfaces. View on Amazon

FAQ

How long does anti-fog coating last on swim goggles?

Results vary with how often you swim and how you store the goggles. Many swimmers reapply before every session to stay consistent. Check your product label for guidance. We also found Top 3 Anti Fog Drops for Swim Goggles That Keep Pool Views Clear useful on this point.

Can I use toothpaste or baby shampoo to anti fog goggles?

Mild baby shampoo is often used for cleaning but is not a true anti-fog treatment, so it will not provide lasting clarity. Toothpaste can be abrasive and may scratch lenses, so avoid it.

Should I consult a professional about my goggles?

If your goggles are prescription or have damaged lenses, ask an optician or eye care professional before applying any treatment. They can advise on what is safe for your specific lens material.

Conclusion

To anti fog swim goggles, clean the lenses, apply a thin even coat of a swim-specific treatment, and rinse or wipe lightly. Repeat the routine before each session and store your goggles carefully. With this habit, you will spend more time watching the wall and less time fighting fog.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our swimming gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Colin Foster
Colin Foster

Colin Foster writes reviews and buying guides for Swim Brief.